Australian Spa Parts

124 - 149 uF Pump motor start capacitor used on some Spaquip pumps. 46mm diameter x 86mm long

Used on 1.5hp 2 spd Waterway Pump amongst others

Waterway 2 & 3 hp 1 speed pumps

Waterway 2.5hp (1.8kw) 2 speed - High Speed

Waterway Tiny Might EMG capacitor

Century Magnetek 2 speed motor centrifugal switch contacts - wishbone styleFound on all Magnetek 2 speed pump motors supplied in Australia by early model Waterway Executive 2hp 2 spd pumps approx 2000, 2001(may be found on...

Signified by 2 blue dots on the shaft sleeve. 112mm diameter, 7mm wide vane

Signified by a yellow,a green & a blue dots on rear of impeller shaft sleeve sticking out back of wet end (can be seen between motor and wet end, unless it has leaked and is broken away)103mm...

Signified by 2 green dots on rear of impeller shaft sleeve sticking out back of wet end (can be seen between motor and wet end, unless it has leaked and is broken away)112mm diameter, 10.7mm wide vane

NO LONGER AVAILABLEAquaflo C Series 2.0 hp impeller - used in rare C series pumps only.Prone to snapping the centre core out of the impeller.Used on Monarch spas with Ultima Controllers.117.5mm diameter, 12mm vane width x 4...

Aquaflo Circ-Master HP circulation pump CMCP1/15th hp, 220-240v, 50Hz, 0.62A, 1425 rpm Used on SCS Industries spas such as Signature Spas, Cyclone Spas, Designer Series Spas, as well as Leisurite and...

2 blue dots on the impeller shaft sleeveAquaflo Flo-Master FMHP 1.5hp impellerDiameter - 94mm, overall height - 94mm, height excluding shaft sleeve - 47mmVane width - internal - 13mm, 8 VanesPart no. marked - 91693701.5hp...

FMXP2 & XP2E body o-ring - can also fit original FMXP pumps, however we recommend replacing the Pump Face Suction Cover with the FMXP2 version listed below.

48FR - 92mm between mounting bolts - centre to centre - volute marked p/n. 92770705

Original FMXP pumps had a slight variation to this current Suction Cover - the body O-Ring was imbedded in a channel around the cover and was a press fit inside the pump body volute (sealed on the side). That style pump face...

Aquaflo FM XP2E 3hp, 56 frame 6.3" diameter complete pump wet end assembly

Slips over front of impeller

Replacement pump only - Aquaflo FMHP 1.5hp, 2 speed pump - used on USA imported spas02115310-2000, 220-240v, 50Hz, 7.9A Emerson Motor.1.5" threads (smaller than 2" threaded fittings used with XP2 pumps...

Spa pump run capacitor - 50uF Aqua-flo pump

Fits XP & XP2 pumps

Adaption for USA made Aquaflo and Waterway pumps with a 1.5" union thread, for connection to 2" pipe. A standard 2" union is supplied with the adaptor ring fitted with o-ring.Fits FMCP, FMHP and other pumps

No longer available

Aquaflo pump threaded bleed plug and o-ring

Davey Spaquip Xcelsior Spa Pool System QX350P350 LPM flow rate220-240v, 50Hz, 10A, 1000w heater with incidental motor heat boosting overall heating capacity to 2400wPlumbing unions spaced at 85mm centre to centre.Perfect...

Has the external appearance of an oversized impeller

Used on Hot Springs Spas

Suits above seal plate and Waterco Portapac spa pumps

Used on Finsbury Vortex spa pumps with electric 4.8kw and 6kw heater elements within the pump casing. Also used on Finsbury Vortex Gas Pack pumps  - Diamond shaped hole for element/sensor penetration into motor...

Temperature sensor pockets for Finsbury 'Gas Pack' spa pumpComes with fibre gasket.EGO sensor bulb diameter (narrow 6mm) for both pocketsObsolete - last one - ONE ONLY

ITT Hydroair Jabsco FloJet Spa circulation pump strainer filter - A vital addition to a circulation pump system to prevent the entry of debris to the pump intake which can quickly cause blockage. Manufactured to withstand...

Laing Autocirc1 hotwater recirculation system.Retrofit version - Simple and quick to fit under the furthest sink from the hotwater system - uses the plumbing already in place.33w, 240v, 50Hz fitted with a timer to allow...

Laing Eco-Circ DC Pump - Solar applications. Brass pump housing.Overtemp safety shutdown, electronic speed / optimal performance controlled pump based on available light / solar panel output and fluid temperature.8-24v DC...

NO LONGER AVAILABLEUse new E-10 pump supercedes this pump

Laing Thermotech E - 10 electronically commutated canned spherical motor centrifugal spa circulation pump60 lpm flow maximum, 6.5m head maximum (double the flow of the standard l 68219 pump listed below)3/4" barb...

3/4" type 7 cup ceramic mechanical seal Suits Finsbury, Waterco Portapac, and others

5/8" type 7 cup ceramic mechanical sealSuits Waterway Executive, Spaquip Scorpio, some Finsbury & Waterco Pumps and others

5/8" type 6 standard ceramic mechanical seal with additional insert.Pump mechanical seal - Suits Aquaflo pumps utilising the clear cup insert.

14mm Euro Mechanical seals prevent water transferring from pump to motor bearingsSome are brand specific such as the Speck seal, others are common to numerous pumps.

Onga 400 series mechanical seal kit - suits 400 series, 4352, 4353, 4395, etcIncludes 1/2" type 6 ceramic and carbon seal, shaft o-ring and shaft sleeve/flinger.

Onga barrel union assembly - swivel style - allows connection with proper seal when pipes are not perfectly aligned.40mm Socket x 50mm Spigot connections.Used on many onga spa, bath and pool pumps

Spa pump motor mounting bolts with rubber vibration pads - used by Sundance Spas and many others. Price per unit.

Suits Spaquip Monster Pump

Spaquip Magnum impeller - 1.5hp. Also available as 3/4 hp, and 1hp1.5hp - 109mm diameter, 7.2mm vane width x 5 vanes, 84mm overall lengthAccomodates a 3/4" standard seal over shaft sleeve.

105mm diameter, 13.4mm vane width, 5 x vanes

Common size used on Signature spas, Lanark Spas and others113mm diameter, 15.7mm vane width, 5 x vanes

Suits Monster Pump - takes 3/4" standard seal.132mm diameter, 5mm vane width

Spaquip QB Series Mechanical Seal AssemblyUnique to this pump type onlyConsists of a 5/8" cup seal with a light spring, combined with a rubber L seal, and a 3/4" standard tapered ceramic.

Spaquip QB Series Pump BodySimilar in appearance to a Waterway Executive. Discharge thread much shorter and different pitch4 x mounting bolts - measurement diagonally between 2 mounting points 148.5mm

Spaquip QB series spa booster pump - 2200w / 3hp, 2 speed with AMP cordset.New fully imported pump.

1hp bath pump - no heater or airswitch.Designed for use with spaquip electronic control heater systems in spa baths or spa pools

Spaquip variable colour LED light - Can only be used with Spa-Quip controllers - Spa Power 400, 600, 800, 1200 series -Lamp comes complete with Spaquip Q3701 Light Housing - Suits 63mm hole size.Lamp can be used with...

Sundance Spas high flow circulation pump impeller (used on Export 50Hz) pumps 2008+ / Aquaflo XP2 impellerIdentified with 4 shaft sleeve coloured dot sequence Green, White, Green, White.111mm diameter, 12mm wide...

Sundance Spas ITT Marlow pump front cover o-ring seal 95-97 export pumpUsed in ITT Jabsco Marlow J250SC-3 Pumps - 220-240v, 50Hz, 8.7-8.3A, 1720w, 2860RPM, EMG motor.

Sundance Spas ITT Marlow pump seal plate rear bracket assemblyMarked on front surface - 4377800Incorporates front pump footUsed in ITT Jabsco Marlow J250SC-3 Pumps - 220-240v, 50Hz, 8.7-8.3A, 1720w, 2860RPM, EMG motor...

Triflo Sensa-Touch 0.8hp multi port dual discharge high flow spa bath pump - jet return via either or both upper pump discharges. Includes air bleed fitting. Spa bath side mounted 2 button electronic switch controlled - pump...

Triflo Sensa-Touch 1hp multi port dual discharge high flow spa bath pump - jet return via either or both upper pump discharges. Includes air bleed fitting. Spa bath side mounted 2 button electronic switch controlled - pump...

Triflo 1.5hp multi port dual discharge high flow spa bath pump - jet return via either or both upper pump discharges. Includes air bleed fitting. Built in airswitch and airtubing supplied.Quiet operation due to optimised...

Triflo spa bath air bleed valve - replacement part. Comes with o-ring

Triflo Spa-Key 1.5hp multi port dual discharge high flow spa bath pump - jet return via either or both upper pump discharges. Includes air bleed fitting. 4 button water resistant remote control operated - heater can be set...

Triflo Xtra-Heat 0.8hp multi port dual discharge high flow spa bath pump - jet return via either or both upper pump discharges. Includes air bleed fitting. Built in airswitch and airtubing supplied.Built in flat plate...

Triflo Xtra-Heat 1hp multi port dual discharge high flow spa bath pump - jet return via either or both upper pump discharges. Includes air bleed fitting. Built in airswitch and airtubing supplied.Built in flat plate...

3/4hp spa bath pump with electric heater for heat retention with airswitch - suits 4-8 jetsWarranty - 1 year

The hp rating listed is actual horsepower.Some manufacturers label pumps with BHP (brake Horsepower)Sold in Australia on 0.75-1hp executive workman pumps5mm vane width x 6 vanes, 116mm diameter. Unarked in suction...

10mm vane width x 6 vanes, 115mm diameter. Marked 3hp in suction throat on most but not all.

Waterway Viper 2.5" pump union assembly

Suits Waterway Executive 3hp pumps sold on Australian spas such as Heritage, Sapphire, Maax, Lanark and others as well as Waterway Executive Euro 3hp Pumps supplied from USA used on LA Spas and others11mm vane...

Waterway centre discharge 1.5hp impeller (USA 2hp)98mm OD, 18.4mm vane width, 5 vanes

Waterway Executive Euro Pump 3hp - Large EMG motor 220-240v, 50Hz, 12.9A, mini JJ lead/plugUsed on LA Spas. Similar 2hp version used on Southwest and Sierra Spas1 year warranty

Wear ring for 1.5hp waterway pump (impeller marked as 3hp)

2 speed pump with JJ plug/lead for Gecko/Balboa/Spaquip systems

2 speed pump with JJ lead/plug for Gecko/Balboa/Spaquip systems

High performance pump with JJ plug/lead - suits up to 20 jets

Front pump face with 2" Suction and drain plugs (8 screws hold it on) Does not include o rings or plugs

Suits Waterway Executive pumpsOriginal Waterway 5/8" ceramic cup seal type 7

Complete wet end (all sizes available 56 Frame)To replace - Simply wind impeller onto the motor shaft without dismantling wet end and do up the 4 mounting bolts.1.75hp / 2hp Southwest/Sierra (4hp USA) wetend utilises a 2.5"...

Waterway Hi Flo 2hp (4hp USA 60hz) impeller96mm diameter x 6 vanes @ 23mm vane width

Standard suction/discharge union on Waterway Executive pumps

The Ultimate Swim Jet System !Waterway River Swim Jet / Waterway Viper Swim Jet Pump System. Waterway River Jet -8" / 200mm wide vertically adjustable eyeball nozzle.Can use up to 350 gpm / 1200 lpm water flow at 6 psi...

1" pump union to suit Waterway Tiny Might with a 3/4" ribbed barb tail for direct connection to 3/4" CVT vinyl tubing

Very small mechanical seal - ceramic 23mm D, carbon 32mm D to extremetiesOriginal Waterway mechanical seal - 3/8" type 7Suits Waterway Tiny Might circulation pump

Waterway Viper pump wetend complete - 2.2kw, (5hp USA)Complete with volute, faceplate, body o-ring, impeller, mechanical seal, and wear ring.Uses a 5/8" standard type 6 seal.O-ring is seated in a groove and seals by...

Waterway Viper pump impeller92mm diameter, 7 x vanes, 19mm vane widthUnique design - approx 30 degree pitched front/rear plates creating a concave rear / convex frontMechanical seal to suit is a 5/8" standard type 6 (not the...