Australian Spa Parts - Spa & Hot tub suction & skimmer fittings
Spa suction fittings used in spa pools and spa baths.
Many suction fittings no longer comply with the current standards requiring specific testing and flow rates to be listed. If you don't see your suction fitting here, this is the likely reason.
For new installations and re-plumbs, the use of approved suctions of the correct flow rate is required.
A pump MUST have a minimum of 2 suction points (or 1 suction and skimmer) each suction having a flow rating equivalent or greater than the pump flow rate. ie combined flow rating of 2 suctions shall be at least double the pumps maximum flow rate.
Some suctions have differing flow ratings depending on installation method and components used.
This category will be undergoing continual change as more suctions become approved.
You must check you pump flow rate requirements when determining the correct suction type required.
Incorrect pump/suction matching may lead to injury or death.
Any doubts, please contact us before purchasing suction fittings or use a qualified spa technician.
See further information below :
• A minimum of two functioning suction outlets per pump must be installed. Suction outlets must be installed a minimum of 600mm apart, as measured from suction pipe center to suction pipe center.
• Dual suction fittings shall be placed in such locations and distances to avoid "dual blockage" by a user.
• Dual suction fittings shall not be located on seating areas or on the backrest for such seating areas.
• The maximum system flow rate shall not exceed the flow rating of any listed suction outlet cover installed. In the event of one suction outlet being completely blocked, the remaining suction outlets serving the system shall have a flow rating capable of the full flow of the pump(s).
• Never use pool or spa if any suction outlet component is damaged, broken, cracked, missing, or not securely attached.
•Replace damaged, broken, cracked, missing, or not securely attached suction outlet components immediately.
•Two or more suction outlets per pump should be installed in accordance with latest standards.
Some suction fittings are available with vacuum break fittings allowing higher flow ratings - this is due to the vacuum break plumbing which, once the suction becomes blocked, will suck air from the vacuum break line / vent into the suction plumbing causing the pump to cavitate and lose suction, thus allowing a trapped person to be freed.
Waterway Suction Installation Instruction Sheets listed in below links for download:
Hi-Flo SPC-2v WITHOUT vacuum break fittings
Hi-Flo SPC-2v with vacuum break fittings
Super Hi-Flo SPC-3v WITHOUT vacuum break fittings
Super Hi-Flo SPC-3v with vacuum break fittings
Ultra Hi-Flo suction
Super Ultra Hi-Flo suction for self contained portable spas
Super Ultra Hi-Flo suction for other installations
Ultra Strip Drain / Suction
Please ensure you download an install sheet if purchasing and installing a Waterway suction fitting.
Discontinued NLA - no longer legal/safe - Replace with this suction fitting listed here and re-plumb to suit. American Products PacFab Hyper Flow spa suction cover These covers break easily. Replacement is e...
CMP spa suction Australian approved flow rate of 355 lpm / 94 GPM 90mm diameter cover. 24mm projection 58mm hole size required 1.5" / 40mm straight slip plumbing socket Two x screws securing cover, but on gr...
17 In Stock
Edgetec suction Australian approved flow rate of 192lpm NB these same suctions were originally rated much higher and used in portable spas with 2-3hp pumps. It is NOT acceptable/legal to replace this sucti...
13 In Stock
Discontinued / No longer Available - Replace with this suction fitting - listed here and re-plumb to suit. Where there is more than one suction associated with the pump connected to the broken suction (there...
S&P Spa Strip Skimmer - utilized on a vast number of spas for many years - most popular style used. 40mm plumbing - complete with street elbow 237mm high x 110mm wide x 25mm deep 60mm holesize required in sp...
52 In Stock
Waterway 10" tru flo drain RETROFIT SUCTION / DRAIN COVER ASSEMBLY - suitable for concrete swimming pool installation where a field built sump / drain setup is used. Frame adaptor screwed to spa / pool wall...
3 In Stock
Waterway 2" Socket x 2.5" spigot 90 degree elbow suction adaptor Can be used with suction fittings or any other application with a 2.5" socket to convert to 2" plumbing pipe...
5 In Stock
Waterway Plastics 90 degree 2" threaded suction adaptor. 2" FPT / BSP female thread x 2" / 50mm socket Screws over the 2" male NPT thread on Waterway 3.5" suction fittings. Also suits any other fitting with ...
97 In Stock
Waterway 2.5" / 65mm sweep elbow - socket x spigot. Suitable for suction fittings, pump connections, etc to maximise flow...
17 In Stock
Waterway 2" socket x 2.5" spigot 90 degree elbow suction adaptor with 3/4" barb for vacuum relief tube connection. Vacuum relief offers greater flow rating and safety for suction fittings....
15 In Stock
Waterway 2.5" spigot x 2" / 50mm socket reducing adaptor - can be used with 2.5" Waterway suctions to reduce to 2" plumbing. Also used with 2.5" Waterway Wye when splitting multiple suctions on swim systems...
11 In Stock
Waterway 3.5" Ultra Hi-Flo suction - White or Grey Flow rated 454 litres per minute 60mm hole size required, 94mm cover diameter, projection of 52mm into spa. Replaces all suctions with up to 60mm hole in t...
Waterway 3.5" Ultra Hi-Flo suction with 90 degree elbow & 2" socket Flow rated at 454 lpm 60mm diameter hole required, 94mm cover diameter, 50mm projection into spa....
Waterway 32" Ultra Strip Drain / Suction - for Fibreglass & Vinyl lined spas & pools - up to 1330 lpm / 352 gpm- grey
Waterway 32" Ultra Strip Drain / Suction - grey for use in fibreglass and vinyl lined pools / spas Wall mounted - flow rated at 1120 lpm with two ports Floor mounted - flow rated at 1330 lpm with two ports 8...
Waterway 32" Ultra Strip Drain / Suction - white for use in concrete pools / spas with field built sumps Wall mounted - flow rated at 1120 lpm with two ports Floor mounted - flow rated at 1330 lpm with two ...
3 In Stock
Waterway 5" Super Hi-Flo suction fitting with stainless steel cover rated at 681 lpm flow 2" / 50mm Socket....
5 In Stock
Waterway 5" Super Hi-Flo suction with 2.5" socket Massive 950 litres per minute flow rated for high output spa and swimjet pumps in portable spa installations. (All other installations ie in-ground, deck, ...
Waterway 5" Super Hi-Flo suction with 2.5" Spg x 2" socket 90 degree elbow adaptor. 950 lpm rated in self contained portable spa, 680 lpm rated in all other applications 130mm diameter cover, 38mm projecti...
Waterway 5" super hi-flo 2.5" suction fitting with straightr 2" socket adaptor vacuum break. Vacuum break 3/4" barb connection MUST be correctly connected and activated to achieve higher flow rating of 878 l...
Waterway 5" super hi-flo 2.5" suction fitting with 2" socket adaptor vacuum break 90 degree elbow. Vacuum break 3/4" barb connection MUST be correctly connected and activated to achieve higher flow rating of...
Waterway 5" Super Ultra Hi-Flo suctions made for portable spa applications - MASSIVE flow rating of 999 lpm for portable spa installation. All other installations these suctions still have an extremely high...
Waterway 5" super ultra hi-flo suction fitting with 2.5" / 65mm socket for plumbing connection. Rated to a MASSIVE 999 lpm for applications where installed in portable spas or swim spas. Perfect for swimjet ...
5 In Stock
Waterway 6" Ultra Suction - white, black, or beige - self aligning slip fit design to push inside Australian 40mm pressure pipe. Screw supplied to secure to the wall. Wall mounted only - flow rated at 291 l...
Waterway 6" Ultra Suction - white, black or beige - self aligning slip fit design to glue inside Australian 50mm pressure pipe. stainless screw included to secure to the wall. Wall mounted only - high flow ...
Waterway Extended Thread HOT TUB 3.5" Ultra Hi-Flo Suction - 454 lpm rated with 90 degree ell 2" Socket
Extended thread Timber Hot Tub Suction Fitting Suits up to 50mm wall/stave thickness - perfect for cedar hot tubs Waterway 3.5" Ultra Hi-Flo suction with 90 degree elbow & 2" socket Flow rated at 454 lpm 60m...
Timber hot tub White or Grey Waterway strip skimmer Suits wall / stave thickness up to 60mm 2" threaded elbow 60mm hole size. Maximum wall thickness - approx 60mm N.B. This strip skimmer does NOT have flow ...
From $77.00 $66.00
Waterway Weir skimmer for use in fibreglass and concrete spas and pools. Hole size required - 150mm wide x 130mm high. Face dimensions - 195mm wide x 185mm high Supplied with mounting screws or you can bo...
Waterway Weir skimmer with stainless steel fascia - for use in fibreglass and concrete spas and pools. Hole size required - 150mm wide x 130mm high. Face dimensions - 195mm wide x 185mm high Supplied with...
Waterway Weir skimmer for use in fibreglass and concrete spas and pools. Hole size required - 150mm wide x 130mm high. Face dimensions - 195mm wide x 185mm high Supplied with mounting screws or you can bolt...
4 In Stock
Waterway Hi Flo suction fitting with 1.5" 90 ell and integral vacuum break. The vacuum break MUST be correctly installed and active to achieve the specified 348 lpm flow rating. Flow rate WITHOUT the vac bre...
This suction has a huge 950 litres per minute flow rating. 130mm cover diameter, projection into spa of 37mm. Hole size required through spa is 84mm 2" / 50mm socket for plumbing connection ...
Waterway Plastics grey strip skimmer Straight 40mm slip connection - suits 40mm / 1.5" pipe. 60mm hole size. Maximum wall thickness - approx 30mm N.B. This strip skimmer does NOT have flow rating. It can onl...
8 In Stock
White Waterway strip skimmer Straight 40mm slip connection - suits 40mm / 1.5" pipe. 60mm hole size. Maximum wall thickness - approx 30mm N.B. This strip skimmer does NOT have flow rating. It can only be use...
21 In Stock
Grey or white Waterway strip skimmer Straight 40mm slip connection with 40mm/1.5" street elbow - glues inside the skimmer fitting - suits 40mm / 1.5" pipe. 60mm hole size. Maximum wall thickness - approx 30m...
Waterway suction vacuum vent fitting with 4 x 3/4" barbs to suit up to 4 tubes for interconnection to spa safety suctions with vacuum break requirements usually due to needing higher flow rates. Usually des...
3 In Stock