Australian Spa Parts - spa heater parts - Elecro, Gecko, Balboa, Davey Spaquip, Hydroquip, Ethink
Spa Heater Parts - various parts for differnet brands of spa heaters other than elements and sensors
Also look under Sensors - Temp, Flow, Pressure for thermostats, water sensors, sensor housings, etc
Suits 1.5" Heater union - not common - one side is flat, the other has a raised rib for better seal - SOLD INDIVIDUALLY Gasket side - outside diameter - 61mm, inside diameter - 40mm O-ring side - diameter ...
Suits 1.5" Heaters - not common - used on some cs7500 Hydroquip packs with elements welded into the tubes and 'may' suit some Chinese made LX Rooster heaters amongst others...
2" heater flat o-ring pair Combination gasket and o ring in one for superior seal - installed each end of the heater tube This is the common size used in almost all stainless steel heaters. Can be used on ma...
29 In Stock
Spa 2" flow through heater male tail - Suits 2" Heaters from Gecko, Hydroquip, Aquatemp, Balboa, RMF, Hydroquip, some Spaquip and others 2" / 50mm socket with male thread for heater locknut to screw onto...
52 In Stock
Suits 2.5" Heater tubes - 2.5" Uni-Nut and split retainer ring - to suit 3" heater housings. NB this is a more unusual larger size than the standard heater tubes fitted to Balboa, Gecko, Hydroquip etc. Do no...
9 In Stock
Suits 2.5" Heater union - not common - one side is flat, the other has a raised rib for better seal - SOLD INDIVIDUALLY Gasket side - outside diameter - 84mm, inside diameter - 70mm O-ring side - diameter o...
2.5" Spa Heater Split Nut The nut has a built in collar to prevent it sliding off the tube. This nut is in 2 halves held together by 2 screws, however once assembled over the tube, threads on and off the uni...
2.5" Spa Heater Split Nut to suit 3" heater tubes The nut has a built in collar to prevent it sliding off the tube. This nut is in 2 halves held together by 2 screws, however once assembled over the tube, th...
2" Aquatemp spa heater uni-nut - female locking nut for union tail connection to heater tube - slides over heater tube flange. Used in conjunction with the Aquatemp Spa Heater Nut Collar. Actual OD is 85mm...
15 In Stock
Aquatemp Spa Heater Uni-Nut Retainer Collar - fits against heater tube flange and prevents nut sliding off. This collar is split to allow fitting over the flange on the tube...
1 In Stock
Used on Balboa heater tubes Sold as a pair Gasket side (with rounded ridge) - outside diameter - 74mm, inside diameter - 53mm Square edged O-ring side - diameter of raised ring centre to centre - 63mm...
112 In Stock
Balboa 2" flow through heater union pair Suits Balboa revolution spa systems and Gecko Aeware in.xm series in.therm heaters 2" / 50mm...
Suits Davey / Spaquip Classic range of electric spa heaters The element screws through this part, The pressure switch capillary screws onto the brass nipple. The heater tank body o-ring seats around the outs...
1 In Stock
Heater element carrier. Suits Davey / Spaquip Spa Power 500A and 500A Mk2 electronic spa controllers Does NOT suit Spa Power 54500 (500) The element screws through this part, The water sensor screws into the...
1 In Stock
O-Ring Kit to suit Davey Spaquip Ampac SP400 / Pulsar / 2095 series / Intuitive series 50mm heater tee Suits: Davey Spa power 400 Spaquip 2095 & Intuitive series Spaqip / Ampac / AquaPacific Pulsar 208x ser...
26 In Stock
Davey Spaquip Spa Power 600 / 601 / 750 / 800 / 1000 / 1200 Heater Tube & Element O-Ring - Oval brass bulkhead style
Davey Spaquip Spa Power plastic heater tube and element o-ring. Suits all models as indicated below ONLY. Existing element must have large oval shaped brass bulkhead to suit. (newer titanium elements have 2 ...
6 In Stock
Elecro Heater spare part - Elecro Heater union to suit Optima Compact heaters sold through Australian Spa Parts Dual size - metric 50mm and 1.5" / 40mm Aus pipe sizes are suited. ABS glue must be used....
3 In Stock
Elecro Heater spare part - Elecro SP-118 O-ring pair to suit Elecro Optima Compact heaters sold through Australian Spa Parts These O-rings seal the male threaded union assembly to the main heater body as per...
6 In Stock
Ethink KL8800 and KL8-3A series heater gasket pair For use with H220 heaters only 1.5" / 40mm plumbing 58mm OD x 45mm ID x 7.5mm thick ribbed square section soft gasket. Underside is 'U' shape slotted to fit...
19 In Stock
Ethink KL8800 and KL8-3A series heater gasket pair For use with H380 heaters only 2.0" / 50mm plumbing 70mm OD x 54mm ID x 8mm thick ribbed square section soft gasket. Underside is 'L' shaped. NB. These gask...
5 In Stock
Used with Gecko USPA / Microspa controllers with external pressure switch or water sensor threaded into this extended 2" heater male tail 2" / 50mm socket, male threaded to suit Gecko heater. 1/8" female thr...
Heater element hardware - element nuts, terminal nuts and o-rings Supplied standard with elements. Available here seperately for repair jobs. Used in USA made heater tubes used in Balboa, Gecko, Spa Builders...
4 In Stock
Heater Element O-ring seal pair - suits USA elements in flow through tubes - Balboa, Gecko, Hydroquip
Spa heater element o-ring seal pair Suits elements installed in flow through heater tubes manufactured by USA spa heater manufacturers including: Balboa Water Group Hydroquip Gecko Brett Aqualine Spa Builder...
50 In Stock
2" Spa Heater Snap Nut Serves same function as the Aquatemp Uni-Nut and Split nuts This heater union nut has a snap in 'C' Clip once the nut has been slipped over the heater tube flange, to lock it together....
27 In Stock
LX Flow Type replacement Gasket Seal pair Suits 1.5" / 40mm tubes / unions These heaters are used on many Chinese manufactured spas with Chinese control systems and can be a replacement for 'Rooster' heate...
38 In Stock
Siemens 50A 2 pole contactor used in spa controller/heater applications. 230v coil, contacts rated at 50A resistive load, 35A inductive load. Replaces similar Hartland branded contactors. Used in Aquatemp ...
1 In Stock
Spaquip 40mm heater tee O-ring Kit 3 x 40mm O-Rings Suits older 40mm symmetrical heater tee's used on: Spaquip / Ampac / AquaPacific / Aquaswim Pulsar series spa controllers 208x series Spaquip / Englefield ...
17 In Stock
DISCONTINUED - NO LONGER AVAILABLE Used in conjunction with Scorpio and Magnum spa and spa bath pumps Suits Pulsar, 2095 and Intuitive series spa controllers as well as Englefield, Wilton and other spa bat...
Spaquip / Davey 'male tail' threaded union section with 50mm/2" spigot x 40mm/1.5" socket. Thread size is 40mm union size (approx 70mm OD) This is a specialty component used on (and supplied with) Spa Pow...
7 In Stock
Used on : 40mm Spaquip barrel unions & pump unions, Heater element O-ring for: Davey Spa Power 400, Spaquip 2095 series & Intuitive series, Spaquip / Ampac / AquaPacific / Aquaswim Pulsar 208x series, Englef...
53 In Stock
40mm Spaquip Pump union / heater union - Suits Scorpio and Magnum pumps, and Spa Power 500 heaters Comprises tail, nut and o-ring...
21 In Stock
Spaquip 50mm heater tee - Used with Monster and Maxi Flow pumps - Suits Pulsar, 2095, Intuitive series and Spa Power 400 controls...
7 In Stock
50mm Spaquip Pump union / heater union - Suits Monster and Maxi Flow pumps, and all Spa Power heater barrels (600, 601, 750, 800, 1000, 1200) Comprises tail, nut and o-ring...
31 In Stock
Spaquip element carrier O ring - fits Classic 2.3kw, 4.5 and 5.5kw heaters, and Spa Power 500 series heaters....
8 In Stock
Davey/ Spaquip heater union retainer ring Limited to stock on hand - do not 'Backorder' if insufficient or nil stock displays. These are used with 50mm heater tee's on: Pulsar series, 2095 series, Intuitive ...
5 In Stock
Spaquip Heater Tube insert - used on pre oct 2015 Spa Power 601, 800, and 1200 systems with low flow circulation pump systems. For these systems without the insert, overheat issues are more likely due to the...
2 In Stock
Available with push on spade terminals or screw down terminals - used in Spaquip Classic heaters and can be used on all single pole spa heaters (6kw max) Rated at 240v, 30A AC1 resistive load....
2" Spa Heater Split Nut - serves same function as the Aquatemp Uni-Nut, however suits older style Aquatemp, and all Balboa, Gecko Electronics, and some other heater tubes with flanges to wide in diameter for...
57 In Stock
2.0kw 2" x 15" heater tube assembly to suit a wide variety of spa control systems Universal design with moveable mounting studs to suit many systems. Multiple pressure switch tapping positions and hi limit s...
5 In Stock
1.5" heater union split nut NOT the common size (2" is most popular) Found on 40mm / 1.5" heater unions - on Dimension One spas and others OD = 72mm Thread = approx 63mm Sleeve collar internal diameter = 49m...
15 In Stock
Waterway Plastics 1.5" flat o-ring gasket pair to suit 1.5" heater tubes. This is NOT the common size - these are suited to smaller than standard heater tubes such as Hydroquip CS7500A control systems with w...
13 In Stock
Waterway Plastics 2" heater flat o-ring gasket pair This is the common size used in almost all stainless steel heaters. Combination gasket and o ring in one for superior seal - installed each end of the heat...
46 In Stock