Australian Spa Parts - USA made Gecko, Balboa, Hydroquip electric spa heater system spare parts
Repalcement spa heater parts for USA manufactured spa control systems from Gecko Electroics, Balboa Water Group, Hydroquip and others
This is the common size used in almost all stainless steel heaters. Combination gasket and o ring in one for superior seal - installed each end of the heater tube Can be used on many brands with similar moun...
210 In Stock
Spa 2" flow through heater male tail - Suits 2" Heaters from Gecko, Hydroquip, Aquatemp, Balboa, RMF, Hydroquip, some Spaquip and others 2" / 50mm socket with male thread for heater locknut to screw onto...
106 In Stock
2.5" Spa Heater Split Nut The nut has a built in collar to prevent it sliding off the tube. This nut is in 2 halves held together by 2 screws, however once assembled over the tube, threads on and off the...
5 In Stock
2.5" Spa Heater Split Nut to suit 3" heater tubes The nut has a built in collar to prevent it sliding off the tube. This nut is in 2 halves held together by 2 screws, however once assembled over the tube, th...
5 In Stock
2" Aquatemp spa heater uni-nut - female locking nut for union tail connection to heater tube - slides over heater tube flange. Used in conjunction with the Aquatemp Spa Heater Nut Collar. Actual OD is 85mm...
23 In Stock
Aquatemp Spa Heater Uni-Nut Retainer Collar - fits against heater tube flange and prevents nut sliding off. This collar is split to allow fitting over the flange on the tube...
7 In Stock
Thermcore Aquatemp heater element wrench. 1/4" and 3/8" sized wrench to suit Thermcore Aquatemp heater element terminals to both hold the terminal post tight and tighten/loosen the terminal nut (2 required) ...
6 In Stock
Used on Balboa heater tubes Sold as a pair Gasket side (with rounded ridge) - outside diameter - 74mm, inside diameter - 53mm Square edged O-ring side - diameter of raised ring centre to centre - 63mm...
149 In Stock
Balboa 2" flow through heater union pair Suits Balboa revolution spa systems and Gecko Aeware in.xm series in.therm heaters 2" / 50mm ...
2 In Stock
Used with Gecko USPA / Microspa controllers with external pressure switch or water sensor threaded into this extended 2" heater male tail 2" / 50mm socket, male threaded to suit Gecko heater. 1/8" female...
2 In Stock
Heater Element O-ring seal pair - suits USA elements in flow through tubes - Balboa, Gecko, Hydroquip
Spa heater element o-ring seal pair Suits elements installed in flow through heater tubes manufactured by USA spa heater manufacturers including: Balboa Water Group Hydroquip Gecko Brett Aqualine ...
42 In Stock
2" Spa Heater Snap Nut Serves same function as the Aquatemp Uni-Nut and Split nuts This heater union nut has a snap in 'C' Clip once the nut has been slipped over the heater tube flange, to lock it together...
47 In Stock
2" Spa Heater Split Nut - serves same function as the Aquatemp Uni-Nut, however suits older style Aquatemp, and all Balboa, Gecko Electronics, and some other heater tubes with flanges to wide in diameter for...
19 In Stock
1.5" heater union split nut NOT the common size (2" is most popular) Found on 40mm / 1.5" heater unions - on Dimension One spas and others OD = 72mm Thread = approx 63mm Sleeve collar internal diameter ...
30 In Stock
Waterway Plastics 2" heater flat o-ring gasket pair This is the common size used in almost all stainless steel heaters. Combination gasket and o ring in one for superior seal - installed each end of the hea...
220 In Stock