Australian Spa Parts - Aquaflo Gecko XP2 & circ-master spa pump parts - impeller, seal, pump body
1.5" MPT threaded adaptor with 1.5" / 40mm Spigot This fitting could be used in numerous applications including alteration to particular pump plumbing/relocation. The thread suits the following pump union...
18 In Stock
2" Spa Pump Union PAIR 2" socket, 2" FBT USA female thread Suits the following pumps: Aquaflo XP & XP2 Waterway Executive & Hi-Flo LX LP & WP series Balboa SuperWow & Ultimax Spanet XS-30 series Davey QB AUS...
61 In Stock
Magic Plastics 2" pump union split nut repair fitting. 2" FPT thread to suit 2" MPT threaded pumps or fittings. This split nut can be used to replace a broken pump union threaded nut without the need for re-...
372 In Stock
Signified by one Orange dot on impeller shaft sleeve Diameter - 98mm, 7mm wide vane x 7 vanes Sold individually. (this impeller is marked and has the same dimensions as the 1hp FMHP pump impeller except the ...
8 In Stock
Signified by Blue / Green / Yellow dots on impeller shaft sleeve Diameter - 103mm, 8mm wide vane x 7 vanes Used in Hot Spring Spas Wavemaster pumps Replaces p/n 91694165 and 91694151...
25 In Stock
XP2E 1.5hp impeller - marked 2hp (2hp 60Hz USA) Signified by 1 Blue dot and 1 Silver dot on the shaft sleeve. 102mm diameter, 6 x vanes, 10mm vane width May be marked '2.0HP - 2200'...
Signified by 2 white dots on the shaft sleeve. 112mm diameter, 8.8mm wide vane Not used on new Australian 50Hz model pumps but was used on Aquaswim pumps in the past....
1 In Stock
XP2E 1.75hp impeller - marked 2.5hp (USA) Signified by 1 Silver dot & 1 x White dot on the shaft sleeve. 104mm diameter, 6 x vanes, 11mm vane width...
1 In Stock
Signified by 2 white dots, seperated by 1 green dot on impeller shaft sleeve (not used on 60Hz USA pumps - would be equivalent to approx 4hp) Diameter - 114mm, 12mm wide vane....
8 In Stock
Signified by 2 green dots on rear of impeller shaft sleeve sticking out back of wet end (can be seen between motor and wet end, unless it has leaked and is broken away) 112mm diameter, 10.7mm wide vane...
29 In Stock
XP2E 2.0hp impeller - marked 3hp (USA) Signified by 3 x Silver and 1 x Orange dots on the shaft sleeve. 108mm diameter, 6 x vanes, 13mm vane width Throat OD 60mm ***Replaces original AF 91695310 signified by...
XP2E 3.0hp impeller - marked 5hp (USA) Signified by 1 Silver dot on the shaft sleeve. 115mm diameter, 7 x vanes, 14mm vane width May be marked '5.0HP - 2500'...
8 In Stock
Aquaflo XP2 impeller - Signified by white - white - blue dots on impeller shaft sleeve Diameter - 104mm, 10mm wide vane x 7 vanes Used on Artesian Spas 50Hz single speed pumps...
One Pink OR Orange dot on the impeller shaft sleeve Aquaflo Circ-Master CMHP / CMCP 1/15th hp impeller Diameter - 95mm, overall height - 92mm, height excluding shaft sleeve - 47mm Vane width - internal - 6.5...
One Red & one Green dot on the impeller shaft sleeve Aquaflo Flo-Master FMHP / FMCP 0.5hp USA impeller Diameter - 87.5mm, overall height - 92mm, height excluding shaft sleeve - 47mm Vane width - internal - 6...
11 In Stock
2 blue dots on the impeller shaft sleeve Aquaflo Flo-Master FMHP 1.5hp impeller Diameter - 94mm, overall height - 94mm, height excluding shaft sleeve - 47mm Vane width - internal - 13mm, 8 Vanes Part no. mar...
One Yellow dot on the impeller shaft sleeve Aquaflo Flo-Master FMHP 1hp impeller - ALSO NOW USED IN AQUAFLO CMHP CIRC-MASTER PUMPS SINCE 2006 WITHOUT A WEAR RING Diameter - 95mm, overall height - 94mm, hei...
10 In Stock
FMXP2 & XP2E body o-ring - can also fit original FMXP pumps, however we recommend replacing the Pump Face Suction Cover with the FMXP2 version...
16 In Stock
Aquaflo Flo Master XP2 complete pump wet end 1.5hp, 2hp & 2.5hp complete wet end - available in 3 configurations 48 frame, 56 frame 6.1" and 56 frame 6.3". You will need to measure between the 4 mounting bol...
Same appearance and function as 48 Frame version above - Difference is the motor mounting bolt spacing. 48 Frame pictured on the left, 56 Frame pictured on the right (spaced further apart - larger diameter m...
3 In Stock
ONE ONLY Artesian Spas XP2 pump suction cover with extended suction intake and 9mm barbed port (requires drilling through to activate) that connects to the variable speed drive control via a tube connection....
Aquaflo XP2 faceplate assembly complete - includes: pump faceplate / suction cover, body o-ring, drain plug, drain plug o-ring Original FMXP pumps had a slight variation to this current Suction Cover - the b...
1.5" Aquaflo pump half union assembly - suits 1.5" BSP threaded heater tails, and pumps from Waterway and Aquaflo - suits FMCP, FMHP, Circ-Master, and EHT Therma-flo bath pumps...
1.5" to 2" Aquaflo pump half union adaptor assembly - suits 1.5" BSP threaded heater tails, and pumps from Aquaflo, Waterway and LX suits FMCP, FMHP, Circ-Master, JA, TDA, DH1.0, EA series LX, and other USA ...
2 In Stock
XP2 / XP2E union o-ring pair - these o-rings are the seal under the locknut on the pipe connection pump unions Suit 2" XP series pumps only. Do not suit other models/brands. Diameter approx 66.5mm, approx ...
21 In Stock
Sundance Spas high flow circulation pump impeller (used on Export 50Hz) pumps 2008+ / Aquaflo XP2 impeller Identified with 4 shaft sleeve coloured dot sequence Green, White, Green, White. 111mm diameter, 12m...
12 In Stock
XP2E wear ring used with XP2E 1.75hp (4hp USA) impeller only . Most other XP2E impellers suit the AF 92380080 wear ring NOT this one. 60mm ID, 71mm OD, 16mm high...
10 In Stock
SPECIAL PRICE 2" 90 degree sweep pump union assembly with 2" socket. Maximize flow from the pump instead of 45 and 90 degree bends. Suits all USA 2" threaded pumps including Waterway Executive and Aquaflo XP...
64 In Stock
5/8" type 6 standard ceramic mechanical seal Suits Aquaflo XP2 (p.n. 92500150 ) , Waterway Viper (not Executive), Piranha Circulation Pumps and plenty of others Dimensions 32mm OD ceramic (including rubber)...
11 In Stock
5/8" type 6 standard ceramic mechanical seal Suits : Aquaflo XP2 (p.n. 92500150 ) , Waterway Viper (not Executive), Piranha Circulation Pumps and plenty of others Dimensions 32mm OD ceramic (including rubber...
1 In Stock
Aquaflo 5/8" type 6 standard ceramic mechanical seal WITH Lexan Cup and O-ring Suits older Aquaflo pumps as well as Hayward pumps as listed Suits: Hayward Power Flo II, LX, Matrix Aquaflo Flo-Master and Tub-...
9 In Stock
5/8" type 6 premium silicon carbide mechanical seal Silicon Carbide primary ring / Silicon Carbide seat seal surfaces with Viton elastomers and stainless steel hardware for superior longevity against abrasi...
138 In Stock
80 frame motor cowl - rear fan cover - suits some Aquaflo XP2 / XP2E pump motors and may suit Waterway Executive motors as well as others. Check dimensions listed for compatability 157mm internal diameter, ...
10 In Stock
90 frame motor cowl - rear fan cover - suits some Aquaflo XP2 / XP2E pump motors and may suit Waterway Executive motors as well as others. Check dimensions listed for compatability 171mm internal diameter, ...
4 In Stock
4 Pack - Waterway and Aquaflo 56 frame pump motor mount screws (bolts) Approx 15mm / 5/8" long thread, Slot Hex Washer head. 4 x #10-32 UNF x 5/8" Waterway and Aquaflo pumps use 4 of these screws to hold the...
167 In Stock
Stainless steel pump faceplate screw (bolt) for Waterway range of spa pumps (Executive, Hi-Flo, Centre Discharge, Viper, EX2, etc) and also suits Aquaflo spa pumps (XP2, Circ-master, FMHP) Approx 15mm long t...
134 In Stock