Australian Spa Parts - Waterway Plastics Executive spa pump wet end parts
Waterway Plastics Executive spa jet pump wet end spare parts
2" Spa Pump Union PAIR 2" socket, 2" FBT USA female thread Suits the following pumps: Aquaflo XP & XP2 Waterway Executive & Hi-Flo LX LP & WP series Balboa SuperWow & Ultimax Spanet XS-30 seri...
30 In Stock
SPECIAL PRICE 2" 90 degree sweep pump union assembly with 2" socket. Maximize flow from the pump instead of 45 and 90 degree bends. Suits all USA 2" threaded pumps including Waterway Executive and Aquaflo XP...
78 In Stock
5/8" type 7 cup ceramic mechanical seal Suits Waterway Executive and most other Waterway pumps, Spaquip Scorpio, Spa Systems Pirahna jet Pumps, some Finsbury & Waterco Pumps and others Also used in Waterway...
110 In Stock
5/8" type 7 (6A) cup silicon carbide mechanical seal Silicon Carbide primary ring / Silicon Carbide seat seal surfaces with Viton elastomers and stainless steel hardware for superior longevity against abras...
91 In Stock
4 Pack - Waterway and Aquaflo 56 frame pump motor mount screws (bolts) Approx 15mm / 5/8" long thread, Slot Hex Washer head. 4 x #10-32 UNF x 5/8" Waterway and Aquaflo pumps use 4 of these screws to...
168 In Stock
Stainless steel pump faceplate screw (bolt) for Waterway range of spa pumps (Executive, Hi-Flo, Centre Discharge, Viper, EX2, etc) and also suits Aquaflo spa pumps (XP2, Circ-master, FMHP) Approx 15mm long t...
369 In Stock
The hp rating listed is actual horsepower.Some manufacturers label pumps with BHP (brake Horsepower) Sold in Australia on 1.5hp pumps with Magnetek motors in the late '90's. If in doubt, read the motor ratin...
1 In Stock
Waterway Plastics Executive spa pump impeller - 3hp (1.5hp 60Hz) Original version - usually grey coloured - 10mm vane width x 6 vanes, 115mm diameter. Marked 3hp in suction throat on most but not all. New 20...
15 In Stock
The hp rating listed is actual horsepower. Some manufacturers label pumps with BHP (brake Horsepower) In the case of a Southwest Sierra Spa 2hp pump, they are sometimes labelled 4hp. The original design imp...
4 In Stock
Magic Plastics 2" pump union split nut repair fitting. This split nut can be used to replace a broken pump union threaded nut without the need for re-plumbing. Suits: Waterway 2" unions used on Waterway E...
80 In Stock
Waterway Executive 2" x 2.5" Pump Buttress Thread Adaptor Use this fitting when replacing older Waterway Executive spa pumps that have a larger 2.5" intake/suction thread than the standard 2" discharge t...
2 In Stock
Waterway Executive Pump Impeller The hp rating listed is actual horsepower. Some manufacturers label pumps with BHP (brake Horsepower) In the case of a 2hp-2.5hp pump, they are sometimes labelled 5hp. If i...
12 In Stock
Suits Waterway Executive 3hp pumps sold on Australian spas such as Heritage, Sapphire, Maax, Lanark and others as well as Waterway Executive Euro 3hp Pumps supplied from USA used on LA Spas and others 11mm v...
6 In Stock
Waterway 6" pump leaf trap with 2" threads - bolt onto any spa boost pump used above water level to ensure flooding. One only - do not 'Backorder' if nil stock displays Suits any pump with a USA 2" NPT...
1 In Stock
Waterway Executive spa pump bleed nipple Threaded - screws into face of pump body in place of standard plug. 6mm barb for connection to air bleed system...
49 In Stock
Front pump face with 2.5" Suction (larger than discharge union) and drain plugs (8 screws hold it on) Does not include o rings or plugs Used on early Waterway Executive pumps and new Southwest Spas / Sierra ...
13 In Stock
IF YOU REQUIRE THIS PRODUCT - WE RECOMMEND YOU PURCHASE COMPLETE WET END INSTEAD (This is due to incompatability issues with new moulding - an older faceplate is too large to fit the newer volutes - no respo...
Complete wet end (all sizes available 56 Frame) To replace - Simply wind impeller onto the motor shaft without dismantling wet end and do up the 4 mounting bolts. 1.75hp / 2hp Southwest/Sierra (4hp USA) wete...
Complete wet end Standard 2" discharge, with larger 2.5" suction intake. This wet end has a much larger thread diameter on the suction than the discharge even though 2" pipe suits both sides. To replace - ...
Waterway 2.5" pump suction union assembly - 2.5" union nut with 2" socket tail piece If the front suction union nut is larger than the discharge union nut, it will be this type - found on early Waterway Exe...
14 In Stock